Duerkopp Adler HP Series Additional guide Manuál s instrukcemi stáhnout pdf (Strana 62)

EFKA AB220A5111

Technician Level

Code no. 190 with control operation

Code no. 1907 with control panel operation

Parameter Designation Unit max min Preset Ind.

132 LSS 0 = Machine start possible with light barrier 1 0 0 *) A

uncovered or covered.

1 = Machine start blocked with light barrier

uncovered if parameter 131 = 1.

Machine start blocked with light barrier

covered if parameter 131 = 0.

133 LSE Thread trimming operation, when completing the seam 1 0 1 *) A

after light barrier sensing On/Off

134 SSt Softstart On/Off 1 0 0 *) A

135 SrS Ornamental backtack On/Off 1 0 0 A

136 FAr Trimming stitch backward On/Off 1 0 0 A

137 hP High lift for walking foot On/Off 1 0 A

139 nIS Display of machine speed On/Off 1 0 0 *) A

141 SGn Speed status for the seam with stitch counting 4 0 0 A

0 = Speed controllable by the pedal up to the set

maximum speed (parameter 111)

1 = Fixed speed (parameter 118) without influence by

the pedal (machine stop by pressing the pedal

to the basic position)

2 = Limited speed controllable by the pedal up to the

set limit (parameter 118)

3 = At fixed speed (parameter 118) can be interrupted

by full heelback

4 = At fixed speed (parameter 110) can be interrupted

by full heelback.

142 SFn Speed status for the free seam and for the seam with 3 0 0 A

light barrier

0 = Speed controllable by the pedal up to the set

maximum speed (parameter 111)

1 = Fixed speed (parameter 118) without influence by

the pedal (machine stop by pressing the pedal

to the basic position)

2 = Limited speed controllable by the pedal up to the

set limit (parameter 118)

3 = At fixed speed (parameter 118) can be interrupted

by full heelback (only for seams with light barrier).

143 kSA Stitch counting at the start of the seam (e. g. chain 3 0 1 A

suction

0 = Speed controllable by the pedal up to the set

maximum speed (parameter 111)

1 = Fixed speed (parameter 112) without influence by

the pedal (machine stop by pressing the pedal

to the basic position)

2 = Limited speed controllable by the pedal up to the

set limit (parameter 112)

3 = At fixed speed (parameter 112), can be suspended

or interrupted depending on the setting of

parameter 019.

144 kSE Stitch counting at the seam end (e. g. chain suction) 3 0 0 A

0 = Speed controllable by the pedal up to the set

maximum speed (parameter 111)

1 = Fixed speed (parameter 113) without influence by

the pedal (machine stop by pressing the pedal

to the basic position)

2 = Limited speed controllable by the pedal up to the

set limit (parameter 113)

3 = At fixed speed (parameter 113), can be suspended

or interrupted depending on the setting of

parameter 019.

*) Depending on the selected mode. See table at the beginning of the List of Parameters!

**) When programming the 3-digit or 4-digit control parameter values (without control panel), the 2-digit or 3-digit

value displayed must be multiplied by 10.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 83 84

Komentáře k této Příručce

Žádné komentáře

Duerkopp Adler HP Series Additional guide Manuál s instrukcemi Strana 62

Komentáře k této Příručce

Související produkty a manuály pro Šicí stroje Duerkopp Adler HP Series Additional guide